5 kg Levelling Coating System RAL7032 - Epoxy Resin | HP-E30VB
5 kg levelling coating RAL 7032 for floors | Epoxy Resin HP-E30VB
The epoxy resin system HP-E30VB is a coloured (similar to RAL 7032 pebbly grey) 2-component epoxy gradient coating with a medium working time for high-quality floor coatings with self-leveling gradient properties.Properties:
- Self-leveling coating mass
- Very good adhesion properties, high abrasion resistance (in system structure with the epoxy resin primer E35GS)
- Very high chemical and mechanical resistance
- High-quality surface, which is easy to clean
- Free of solvents
- Free of substances of very high concerns (SVHC)
- Coloured (grey, anthracite, green)
- Packaging sizes: 5 kg or 25 kg in a bucket
Field of application:
- Applicable on cement bounded surfaces
- For filling and smoothing of damaged floor areas
- High quality surface finishing indoors and outdoors
- Renovation of damagede and rough floors in workshops, garages, feeding tables in livestock farming, slaughterhouses, floors within the livestock keeping etc.
- Not applicable on curved or flexible surfaces
Technical Data Epoxy System E30VB
- Working Time (pot life): 30 minutes (100g at 20°C)
- Working temperature (minimum): 15 °C
- Mixing Ratio (by weight): 100 parts resin : 17 parts hardener
- Mixed Viscosity: high viscous
Working notes
Below you will find processing information (preparing and applying) for the epoxy resin E30VB.
1. Preparing the subsoil:
The self-levelling coating mass E30VB can be applied on new and old surfaces. The surface should be dust-free, rough, clean and dry. Before coating, mechanical smoothen or sealed floors should be sanded or sandblasted. Missing or broken out areas in the surface should be filled by suitable cement mortar or epoxy resin filler HP-E30S (affected areas should be primed with epoxy resin E35GS). Afterwards, the primer E35GS should be applied on the entire surface. The primer is an epoxy resin barrier layer preventing moisture and a bonding agent between mineral surface and subsequent coatings. About 10% of thinner E35GS should be added to the primer system for optimal penetration into the pores.2. Applying of coloured self levelling coating E30VB:
After mixing both components of E30VB thoroughly and intensively, pour the mass on the surface and spread it with a squeegee or a scratch spatula. Then vent the surface with the nobby roller (HP-L1021) for minimizing air bubbles risen in the pores of the underground. This venting process should be repeated multiple times with a time delay between each process. If coating should be applied slip-resistant, fire-dried quartz sand can be applied.3. Recommended tools for processing:
Nobby roller 24 cm (HP-L1021), telescopic rod (HP-L1024), tooth rake, drill with attachment for stirrer agitator.
Hazard Statements
Resin:
Warning
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.
Hardener:
Danger
H302+H332 Harmful if swallowed or if inhaled.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H412 Harmful to aquatic life with long lasting effects.
Resin:
Warning
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.
Hardener:
Danger
H302+H332 Harmful if swallowed or if inhaled.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H412 Harmful to aquatic life with long lasting effects.
