2 kg Coating System RAL7032 - Epoxy Resin | HP-E30RB
2 kg Coating System RAL7032 for floors and walls | HP-E30RB
The epoxy resin system HP-E30RB is a coloured (similar to RAL 7032 pebbly grey) 2-component epoxy roll coating with a medium working time for high-quality floor and wall coatings.Properties:
- Rollable and spreadable coating mass for floor and wall coatings
- Very good adhesion properties, high abrasion-resistance (in combination with our primer E35GS)
- If needed, anti-slip material can be added
- Very high chemical and mechanical resistance
- High-quality surface, which is easy to clean
- Free of solvents, can be thinned with thinner HP-XB (maximum up to 5 %)
- Coloured (grey, anthracite, green)
- Easy processing as "do it yourself" system solution
Field of application:
- Applicable on cement bonded surfaces
- For coatings of new and slightly porous surfaces
- High quality surface finishing for walls and floors outdoors and indoors
- Areas of application are floors in workshops, garages, feeding tables within livestock farming, slaughterhouses, milking stalls, floors within livestock keeping etc.
Technical Data Epoxy System E30RB
- Working Time (pot life): 30 minutes (100g at 20°C)
- Working temperature (minimum): 15 °C
- Mixing Ratio (by weight): 100 parts resin : 22 parts hardener
- Mixed Viscosity: viscous
Working notes
Below you will find processing information (preparing and applying) for the epoxy resin E30RB.
1. Preparing the subsoil:
The roller applied coating E35GS can be applied on new and slightly porous surfaces. The surface should be dust-free, rough, clean and dry. Before coating, mechanical smoothen or sealed floors should be sanded or sandblasted. Missing or broken out areas in the surface should be filled by suitable cement mortar or epoxy resin filler HP-E30S (affected areas should be primed with epoxy resin E35GS). Afterwards, the primer E35GS should be applied on the entire surface. The primer is an epoxy resin barrier layer preventing moisture and a bonding agent between mineral surface and subsequent coatings. About 10% of thinner E35GS should be added to the primer system for optimal penetration into the pores.2. Applying of coloured roller applied coating E30RB:
After pouring component B into component A and mixing them thoroughly and intensively, you can distribute the mixture evenly over the primed surface using a roller. At warmer temperatures we recommended you to pour out the entire bucket in order to achieve a user-friendly processing time. Furthermore we advise you to apply E30RB in two layers. In wall areas multiple thin layers should be applied. If coating should be applied slip-resistant, fire-dried quartz sand can be applied between the first and second layer. Optionally, up to 5% thinner (HP-XB) can be added for a better spreading.3. Recommended tools for processing:
Telescopic rod (HP-L1024), polyamide roller 25 cm (HP-L1026), polyamide roller 15 cm (HP-L1017), plastic bucket 14 lt. (HP-L1050), electric drill, stirrer quirl for electric drill.
Hazard Statements
Resin:
Warning
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.
Hardener:
Danger
H302+H332 Harmful if swallowed or if inhaled.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H412 Harmful to aquatic life with long lasting effects.
Resin:
Warning
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.
Hardener:
Danger
H302+H332 Harmful if swallowed or if inhaled.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H412 Harmful to aquatic life with long lasting effects.
