Subscribe to Newsletter

 
 
83 g/m² Peel Ply Plain (Width: 10 cm) | HP-P83P10
Peel Ply Plain 83 g/m² (Width: 10 cm) | HP-P83P10
Preview: 83 g/m² Peel Ply Plain (Width: 10 cm) | HP-P83P10
Preview: Peel Ply Plain 83 g/m² (Width: 10 cm) | HP-P83P10
83 g/m² Peel Ply Plain (Width: 10 cm) | HP-P83P10
83 g/m² Peel Ply Plain (Width: 10 cm) | HP-P83P10
Peel Ply Plain 83 g/m² (Width: 10 cm) | HP-P83P10
Mobile Preview: 83 g/m² Peel Ply Plain (Width: 10 cm) | HP-P83P10
Mobile Preview: Peel Ply Plain 83 g/m² (Width: 10 cm) | HP-P83P10

83 g/m² Peel Ply Plain (Width: 10 cm) | HP-P83P10

Product No.:
HP-P83P10-H
Shipping time:
ca. 1-3 days ca. 1-3 days (abroad may vary)
on request
Ask about product
Description

83 g/m² Peel Ply Plain (Width: 10 cm) | HP-P83P10

It is made of Nylon and is added into epoxy- or polyester resins as the first and/or last layer of the construction. After hardening, just before further processing it has to be peeled of slowly and in a sharp angle. The Peel Ply leaves an evenly rough, lubricant film free and adhesive surface behind. Sanding or cleaning of the surface is not necessary before sticking or coating. The Peel Ply can´t remain in the construction therefore is a red or blue tracer thread woven into the fabric.

Weight: 83 g/m²
Weave: Plain
Width: 10 cm
Length: 100 mtr.
Material: Nylon 6.6 cleaned

Yarn type specifications:
Warp: 19 y/cm
Weft: 16 y/cm
 
Technical Data Sheet Carbon Fabric HP-P200C


Advantages of Peel Ply Fabric:

  • Accurate upper surface
  • A bit rough after tearing off, absolutely clean and free of dust
  • Ideal subsoil for bonding or further laminating/painting
  • Saves time, no need to grind with sand-paper or removing of grinding dust
In some cases it is desired to have a slip resistance of the component (e.g. stand space of surf boards, boat decks). The surface is after tearing the Peel Ply off ready for use.


► Laminate calculator
Here you can calculate specific values for the vacuum infusion.
 
Working Notes & Support

Working Notes:
In this instruction you will find tips & tricks by working with reinforcement fabrics:
Boat Building (PDF)

further working notes you will find here

 
Laminate Calculator:
Here you can calculate specific values for different fibers, resins and processes:
Laminate Calculator

 

Characteristics of Peel Ply Constructions:

Peel Ply are available in plain or twill. The important characteristics you will find below:
 
Plain
Plain
  • The simplest weave
  • Very slip-resistant
  • Bad drapability
  • Suitable for flat plates or easy moulds

Twill
Twill
  • Diagonally running lines are characteristic
  • Better drapability than plain weave
  • Less slip-resistant
  • Suitable for complicated geometries
Product Safety
Product Safety (GPSR):
Here you will find information for the safe use of peel ply:
Product information for safe handling (PDF)

This product is compatible with (for example):

High Performance Laminating Resin Epoxy HP-E56L
High Performance Laminating System - Epoxy...

The Epoxy-System HP-E56L is an unfilled, low viscous, 2-component combinations of resin and hardener with a processing time of 55 minutes.

Compared to standard resins, our high performance resins show faster curing processes. The laminates have distinctive static and dynamic strengths and they are higher temperature resistance.

⚠️ Important Notice – Shipping in Germany only to Business Customers:
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E55L, this epoxy resin can be shipped to private customers in Germany without any restrictions.

Sales to international customers, whether private or commercial, are possible without any restrictions.
from 5,50 EUR
Infusion Connector | HP-VZ1550
Infusion Connector 12 mm | HP-VZ1550
No imprints in the laminate and easy handling combined with the vacuum flat channel HP-VZ1520 (50 mm) or HP-VZ1530 (100 mm)
3,96 EUR
Sealant Tape | HP-ST12X3/80
Sealant Tape | HP-ST12X3/80
Material: Butyl Rubber
Width: 12 mm
Thickness: 3 mm
Length: 15 mtr.
10,41 EUR
Spray adhesive 400 ml | HP-FIX400
Spray adhesive 400 ml | HP-FIX400
  • To fix reinforcing fabrics (carbon, glas, aramid, …) core materials or vacuum aids in place
  • Application in combination with the epoxy resins from HP-Textiles
  • Excellent spray control with adjustable spray button and dosage valve
  • Bonding wood, textiles, rubber, foams, many synthetic materials, paper and other base materials
11,84 EUR
11,84 EUR per pcs.
80 g/m² Non-woven absorber | HP-VP80P
80 g/m² Non-woven absorber | HP-VP80P
Material: 100% polyester (black)
Weight: 80 g/m²
Width: 80 cm
2,69 EUR

This product is similar to:

MTI®-hose HP-MTI-08
MTI®-hose HP-MTI-08
The MTI® - hose is the new innovation in the branch of vacuum infusion. This new technology will provide more quality, less costs and better mechanical properties.
from 27,80 EUR
5,56 EUR per

Customers who bought this product bought also the following products:

83 g/m² Peel Ply Plain (Width: 15 cm) | HP-P83P15
83 g/m² Peel Ply Plain (Width: 15 cm) | HP-P83P15...
Weight: 83 g/m²
Weave: Plain
Width: 15 cm
Roll length: 100 mtr.
Material: Nylon 6.6
43,73 EUR
High-Gloss Release Agent Carnauba Wax Paste
High-Gloss Release Agent - 700g Carnauba...
  • Wax release agent for brilliant high glossy finish in moulds with smooth, non porous surfaces (metal, plastics, varnished wood or MDF)
  • Suitable for most composites mould applications with solvent free epoxy and polyester resins
  • Primer for film release agent HP-PVA
  • High-gloss release agent for working with In-Mould Coating HP-IMC (HP-Textiles)
27,95 EUR
39,93 EUR per Kg
10 cm Velour Roller | HP-L1015
10 cm Velour Roller | HP-L1015
Width: 10 cm
Pile hight: 4 mm
1,25 EUR
Stirrer with metal propeller | HP-L1051
Stirrer with metal propeller | HP-L1051
Measures:  85 x 400 mm
Colour: Red
3,34 EUR