





MTI®-hose HP-MTI-08
MTI®-hose HP-MTI-08
- Product No.:
- HP-MTI08-5
- Shipping time:
-
ca. 1-3 days (abroad may vary)
- Stock:
- Roll(s)
MTI®-hose
The MTI® - hose is the new innovation in the branch of vacuum infusion. This new technology will provide more quality, less costs and better mechanical properties
The pores of the hose membrane are very small, holding the resin back and only leaving the air through the pores.
Advantages
- Less investment needed for extra machines and materials
- Cures the work in the same way as with any other vacuum techniques
- Reduce the trapped gas and air within the component part
- Minimisation of dry spots
- The results are: high process quality as well as an excellent build quality
HP-MTI® flyer
The MTI® - hose is the new innovation in the branch of vacuum infusion. This new technology will provide more quality, less costs and better mechanical properties
The pores of the hose membrane are very small, holding the resin back and only leaving the air through the pores.
Advantages
- Less investment needed for extra machines and materials
- Cures the work in the same way as with any other vacuum techniques
- Reduce the trapped gas and air within the component part
- Minimisation of dry spots
- The results are: high process quality as well as an excellent build quality
HP-MTI® flyer
Technical data
ID-Diameter (Ø): 8mm
AD-Diameter (Ø): 15mm
Max. operation temperature: 80°C
Exhaust capacity/m by pabs. 50mpas: < 50l/m
Suitable for: EP / UP
Datasheet HP-MTI®
This product is compatible with (for example):

- Transparent, low shrink-casting with tacky-free surfaces
- Very good flow behaviour (low-viscosity)
- Cold-hardening, demouldable at room-temperature
- High fillable casting resin
- Cause pressure-resistant and impact-resistant (tough) moulds / components with high strength and very less shrinkage
Shippingtime:
ca. 1-3 days
from 5,50 EUR
Shippingtime:
ca. 1-3 days

The Epoxy-System HP-E56L is an unfilled, low viscous, 2-component combinations of resin and hardener with a processing time of 55 minutes.
Compared to standard resins, our high performance resins show faster curing processes. The laminates have distinctive static and dynamic strengths and they are higher temperature resistance.
⚠️ Important Notice – Shipping in Germany only to Business Customers:
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E55L, this epoxy resin can be shipped to private customers in Germany without any restrictions.
Sales to international customers, whether private or commercial, are possible without any restrictions.
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E55L, this epoxy resin can be shipped to private customers in Germany without any restrictions.
Sales to international customers, whether private or commercial, are possible without any restrictions.
Shippingtime:
ca. 1-3 days
from 5,50 EUR
Shippingtime:
ca. 1-3 days
This product is similar to:

- Regulates itself the infusion of resin
- No resin pooling at inlet point
- Fibres are evenly covered with resin
- Homogeneous laminate
- Optimum fibre volume ratio
- Highest quality of parts with reproducible results
- Working hours and its costs can be saved
Shippingtime:
ca. 1-3 days
4,64 EUR
Shippingtime:
ca. 1-3 days
Customers who bought this product bought also the following products:

- Water based release agent for applications with In-Mould Coatings (HP-IMC) from HP-Textiles.
- Also suitable for solvent free epoxy resins, unsaturated polyester resin and vinyl ester resins.
- Fast drying time (per layer <5 minutes at 20°C)
- Semipermanent, external release agent with good demoulding features
- Minimises remains on the moulds’ surface – and at the same time no transmission to the component
from 9,88 EUR