Subscribe to Newsletter

 
 
Spiral Tube for vacuum moulding | HP-ST100
Spiral Tube for vacuum moulding | HP-ST100

Spiral Tube for vacuum moulding | HP-ST100

Product No.:
HP-ST100
ca. 1-3 days ca. 1-3 days (abroad may vary)
from 8,95 EUR

incl. 19% tax excl. Shipping costs

This product is compatible with (for example):

High performance laminating system HP-E29L

The Epoxy-System HP-E29L is an unfilled, low viscous, 2-component combinations of resin and hardener with a processing time of 25 minutes.

Compared to standard resins, our high performance resins show faster curing processes. The laminates have distinctive static and dynamic strengths and they are higher temperature resistance.

on request
Spiral hose connector | HP-VZ1540
Spiral hose connector for easy connection of the vacuum infusion pipe.
Suitable for 12 mm pipe and spiral hoses up to 14,6 mm outside diameter.
4,68 EUR
High Performance Laminating Resin Epoxy HP-E56L

The Epoxy-System HP-E56L is an unfilled, low viscous, 2-component combinations of resin and hardener with a processing time of 55 minutes.

Compared to standard resins, our high performance resins show faster curing processes. The laminates have distinctive static and dynamic strengths and they are higher temperature resistance.

on request
Stirrer 28 cm plastic
Colour: Black
Material: Plastic
Size: 28 cm incl hole and retaining hooks
0,95 EUR
PE hose for vacuum moulding standard | HP-VZ1010
The PE-Hose is used in the vacuum-injection (vacuum-infusion) process. It can be used mainly as a disposable product in combination with our connectors POM.
 
Available dimensions:
Material: PE
Outer-Ø: 10 mm
Inner-Ø: 8 mm
1,33 EUR

This product is similar to:

Epoxy resin for infusion process HP-E30RI

The injection- / infusion-resins of the series HP-E3000RI show very low viscosities,
what supports excellent wet-out and flow properties.
The hardener HP-E30RI allows a pot-life of 30 minutes. The series is usable for hand-laminating too.

Vacuum Infusion, Pressure Injection

from 61,90 EUR
Polyester resin based on orthophtalic acid -Resin & Hardener- | HP-P21LPG
NEW

  • Unsaturated Polyester Resin
  • Orthophtalic-based, pre-accelerated, high thixotropic index
  • Wax free, tacky for further bonds / layers
  • Good mechanical properties
  • Excellent wet-out of fiberglass, carbon and aramid fibers
  • LSE (Low Styrene Emission) polyester resin
  • Applicable for hand lay-up, spray-up and for general reinforced plastics
  • Contains peroxide-indicatorLimited Shipping 
instead 75,90 EUR
only 68,31 EUR
You save 10%
6,83 EUR per Kg
Spiral hose connector | HP-VZ1540
Spiral hose connector for easy connection of the vacuum infusion pipe.
Suitable for 12 mm pipe and spiral hoses up to 14,6 mm outside diameter.
4,68 EUR
Casting system resin transparent HP-E50GB
  • Transparent, low shrink-casting with tacky-free surfaces
  • Very good flow behaviour (low-viscosity)
  • Cold-hardening, demouldable at room-temperature
  • High fillable casting resin
  • Cause pressure-resistant and impact-resistant (tough) moulds / components with high strength and very less shrinkage

from 5,50 EUR

Customers who bought this product bought also the following products:

Mould Covering Epoxy Resin HP-E30FB
The Epoxy Resin System HP-E30FB is an aluminium-filled, high-viscosity combination of resin and hardener with high hardness.

Mould covering system, 30 minutes working time
from 28,90 EUR