Main page » Vacuum Technology » Peelply » Twill » 105 g/m² Peel Ply Twill | HP-T105P100

Preview: Peel ply twill 105g/m² Laminating aid

105 g/m² Peel Ply Twill | HP-T105P100

Mobile Preview: Peel ply twill 105g/m² Laminating aid

105 g/m² Peel Ply Twill | HP-T105P100

Product No.:: HP-T105P100-H
Shipping time:: ca. 1-3 days (abroad may vary)
Stock:: m²

Sliding scale prices

1-4,9 m²: per 4,17 EUR
5-9,9 m²: per 3,75 EUR
10-24,9 m²: per 3,33 EUR
25-49,9 m²: per 2,92 EUR
50-99,9 m²: per 2,50 EUR
100-199,9 m²: per 2,17 EUR
> 199,9 m²: per 1,92 EUR

4,17 EUR

incl. 19% tax excl. Shipping costs

Description

105 g/m² Peel Ply Twill (Width: 100 cm) | HP-T105P100

It is made of Nylon and is added into epoxy- or polyester resins as the first and/or last layer of the construction. After hardening, just before further processing it has to be peeled of slowly and in a sharp angle. The Peel Ply leaves an evenly rough, lubricant film free and adhesive surface behind. Sanding or cleaning of the surface is not necessary before sticking or coating. The Peel Ply can´t remain in the construction therefore is a red or blue tracer thread woven into the fabric.

Weight: 105 g/m²

Weave: Twill
Width: 100 cm
Material: Nylon 6.6 cleaned

Yarn type specifications:
Warp: 21 y/cm

Weft: 21 y/cm

Advantages of Peel Ply Fabric:

Accurate upper surface
A bit rough after tearing off, absolutely clean and free of dust
Ideal subsoil for bonding or further laminating/painting
Saves time, no need to grind with sand-paper or removing of grinding dust

In some cases it is desired to have a slip resistance of the component (e.g. stand space of surf boards, boat decks). The surface is after tearing the Peel Ply off ready for use.

► Laminate calculator
Here you can calculate specific values for the vacuum infusion.

Delivery notes for this product:
Delivery up to 2,5 m² only folded up. More than 3 m² only on roll.

Working Notes & Support

Working Notes:
In this instruction you will find tips & tricks by working with reinforcement fabrics:
Boat Building (PDF)

further working notes you will find here

Laminate Calculator:

Here you can calculate specific values for different fibers, resins and processes:
Laminate Calculator

Characteristics of Peel Ply Constructions:

Peel Ply are available in plain or twill. The important characteristics you will find below:

Plain

The simplest weave
Very slip-resistant
Bad drapability
Suitable for flat plates or easy moulds

Twill

Diagonally running lines are characteristic
Better drapability than plain weave
Less slip-resistant
Suitable for complicated geometries

Product Safety

Product Safety (GPSR):
Here you will find information for the safe use of peel ply:
Product information for safe handling (PDF)

This product is compatible with (for example):

PE hose for vacuum moulding standard | HP-VZ1010...

The PE-Hose is used in the vacuum-injection (vacuum-infusion) process. It can be used mainly as a disposable product in combination with our connectors POM.

Available dimensions:
Material:	PE
Outer-Ø:	10 mm
Inner-Ø:	8 mm

1,33 EUR

Hose connector straight 10/10mm HP-VZ1310

Push Connector 10/10mm HP-VZ1310

- Push connector for easy connection
- both sides of the same diameter
- for tubes with a inside-diameter of 10mm

Compatible with vacuum hose:
HP-VZ1020

"Image similar"

0,81 EUR

Vacuum Bagging Film (Width: 150 cm) | HP-VFT70-150

70 g/m² Vacuum Bagging Film Tube | HP-VFT70/150...

Material:	PE / PA / PE
Weight:	70 g/m²
Width:	150 cm
Colour:	transparent

2,92 EUR

Infusion System - Epoxy Resin | HP-E300GL...

The hardener HP-E300GL allows a pot-life of 300 minutes. The basis of the series HP-E3000GL is an unfilled epoxy-resin, which is mixable with different hardeners for every individual purpose.

Vacuum Infusion, Pressure Injection

⚠️ Important Notice – Shipping in Germany only to Business Customers:
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E300RI, this epoxy resin can be shipped to private customers in Germany without any restrictions.

Sales to international customers, whether private or commercial, are possible without any restrictions.

from 56,50 EUR

Spray adhesive 400 ml | HP-FIX400

To fix reinforcing fabrics (carbon, glas, aramid, …) core materials or vacuum aids in place
Application in combination with the epoxy resins from HP-Textiles
Excellent spray control with adjustable spray button and dosage valve
Bonding wood, textiles, rubber, foams, many synthetic materials, paper and other base materials

11,84 EUR
11,84 EUR per pcs.

Customers who bought this product bought also the following products:

Epoxy resin for infusion process HP-E30RI

Infusion System - Epoxy Resin | HP-E30RI

The injection- / infusion-resins of the series HP-E3000RI show very low viscosities,
what supports excellent wet-out and flow properties. The hardener HP-E30RI allows a pot-life of 30 minutes. The series is usable for hand-laminating too.

Vacuum Infusion, Pressure Injection

from 61,90 EUR