



83 g/m² Peel Ply Plain (Width: 60 cm) | HP-P83P60
83 g/m² Peel Ply Plain (Width: 60 cm) | HP-P83P60
- Product No.:
- HP-P83P60
- Shipping time:
-
ca. 1-3 days (abroad may vary)
- Stock:
- m²
Sliding scale prices
- 1-4,9 m²
- per 3,75 EUR
- 5-9,9 m²
- per 3,33 EUR
- 10-24,9 m²
- per 2,92 EUR
- 25-59,9 m²
- per 2,50 EUR
- 60-119,9 m²
- per 2,17 EUR
- 120-239,9 m²
- per 1,92 EUR
- > 239,9 m²
- per 1,76 EUR
83 g/m² Peel Ply Plain (Width: 60 cm) | HP-P83P60
It is made of Nylon and is added into epoxy- or polyester resins as the first and/or last layer of the construction. After hardening, just before further processing it has to be peeled of slowly and in a sharp angle. The Peel Ply leaves an evenly rough, lubricant film free and adhesive surface behind. Sanding or cleaning of the surface is not necessary before sticking or coating. The Peel Ply can´t remain in the construction therefore is a red or blue tracer thread woven into the fabric.
► Laminate calculator
Here you can calculate specific values for the vacuum infusion.
Delivery notes for this product:
Delivery up to 2,5 m² only folded up. More than 3 m² only on roll.
Weight: 83 g/m²
Weave: Plain
Width: 60 cm
Material: Nylon 6.6 cleaned
Yarn type specifications:
Warp: 19 y/cm
Warp: 19 y/cm
Weft: 16 y/cm

Advantages of Peel Ply Fabric:
- Accurate upper surface
- A bit rough after tearing off, absolutely clean and free of dust
- Ideal subsoil for bonding or further laminating/painting
- Saves time, no need to grind with sand-paper or removing of grinding dust
► Laminate calculator
Here you can calculate specific values for the vacuum infusion.

Delivery up to 2,5 m² only folded up. More than 3 m² only on roll.
Working Notes:
In this instruction you will find tips & tricks by working with reinforcement fabrics:
Boat Building (PDF)
further working notes you will find here
Laminate Calculator:
Here you can calculate specific values for different fibers, resins and processes:
Laminate Calculator
Laminate Calculator
Characteristics of Peel Ply Constructions:
Peel Ply are available in plain or twill. The important characteristics you will find below:
Plain
![]() |
|
Twill
![]() |
|
Product Safety (GPSR):
Here you will find information for the safe use of peel ply:
Product information for safe handling (PDF)
Here you will find information for the safe use of peel ply:
Product information for safe handling (PDF)
This product is compatible with (for example):

The Epoxy-System HP-E56L is an unfilled, low viscous, 2-component combinations of resin and hardener with a processing time of 55 minutes.
Compared to standard resins, our high performance resins show faster curing processes. The laminates have distinctive static and dynamic strengths and they are higher temperature resistance.
⚠️ Important Notice – Shipping in Germany only to Business Customers:
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E55L, this epoxy resin can be shipped to private customers in Germany without any restrictions.
Sales to international customers, whether private or commercial, are possible without any restrictions.
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E55L, this epoxy resin can be shipped to private customers in Germany without any restrictions.
Sales to international customers, whether private or commercial, are possible without any restrictions.
Shippingtime:
ca. 1-3 days
from 5,50 EUR
Shippingtime:
ca. 1-3 days

The hardener HP-E300GL allows a pot-life of 300 minutes. The basis of the series HP-E3000GL is an unfilled epoxy-resin, which is mixable with different hardeners for every individual purpose.
Vacuum Infusion, Pressure Injection
Vacuum Infusion, Pressure Injection
⚠️ Important Notice – Shipping in Germany only to Business Customers:
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E300RI, this epoxy resin can be shipped to private customers in Germany without any restrictions.
Sales to international customers, whether private or commercial, are possible without any restrictions.
Due to legal regulations (ChemVerbotsV), this product may be shipped within Germany only to business customers. Foreign customers can receive this product via shipping. A technically comparable alternative is our HP-E300RI, this epoxy resin can be shipped to private customers in Germany without any restrictions.
Sales to international customers, whether private or commercial, are possible without any restrictions.
Shippingtime:
ca. 1-3 days
from 56,50 EUR
Shippingtime:
ca. 1-3 days
This product is similar to:

- High-quality mould covering resin
- Non-drip, without run-off on vertical surfaces -high thixotropic, blue-grey coloured
- Vacuum degassed
- User friendly mixing ratios (100:10)
- For abrasion-and breaking resistance surfaces with good thermal conductivity.
- Innovative formulation, free of DETA1 with high styrene resistance.
Shippingtime:
ca. 1-3 days
from 29,90 EUR
Shippingtime:
ca. 1-3 days